Newton Poetry

The Newton eMate 300 is a great machine. Small, portable, rugged – a sort of proto-netbook that lets you type on the go. And the battery life is great if you have a working, rechargeable battery with plenty of juice.

When my eMate came, I found out right away that the battery pack was probably the original. It held a charge for about three minutes. So while it’s handy to pop a few fresh AA batteries into a MessagePad and be back up and running, the eMate relies on its single battery pack. If it goes, you’re stuck with replacing it, building a new one from scratch, or keeping your eMate plugged in at all times.

I opted for the simplest solution: buy a new battery pack on eBay and installing it myself.

To start, I grabbed a new eMate battery pack from PowerBook Guy, a Torx wrench (I actually took my eMate into the hardware store to get the perfect-sized wrench), my eMate, and some starting instructions from Frank.

The first step is to flip your eMate over. See that half-circle hatch near the handle (above)? That’s what you’re taking off.

There are just two screws to remove on the cover, and they’re both at the top.

I left the screws in their slots as I lifted the cover off so I wouldn’t lose them. Now you see the good stuff: a few memory slots and the battery.

The battery pack isn’t bolted to the eMate; it simply rests in a little trench, with a wire attached to the circuit board.

This is the most delicate of the steps: pulling the battery connection cable away from the circuit board. Be careful, and use something (I used my fingernail) to wedge the connector away from the plug-in.

From here, pull the battery pack out of the eMate. The actually battery pack fits snugly inside the holster, but slides right out.

Here’s what the empty battery tray looks like inside the eMate. The soft pads keep the battery pack case from sliding around inside the Newton.

Slide your new battery back inside the protective casing, with the connection wire sticking out of the right-hand side.

Now carefully slide the connection wire into the circuit board until it snaps tight. A little push on the white part will be plenty.

Place the battery case inside the eMate, replace the cover, and tighten your screws. That’s all.

I plugged my eMate in and let it charge a whole day, and now it’s like I have a whole new eMate. A fully-charged battery pack should last you for days, even with heavy usage.

The battery pack cost me about $20 (plus shipping) on eBay. There are some DIY die-hards who are all about making their own battery pack, but the soldering made me nervous. Maybe someday I’ll give it a try. This solution, however, worked fine for me.

Now my eMate is truly portable because I don’t have to worry about keeping it plugged in at all times. Replacing the battery pack was a cinch, too, and took all of about five minutes.

Everytime I see an “i” prefixing some word, I can’t help but think of how Apple created a naming convention that, to this day, continues to attract marketers and product designers. What began as the iMac turned into iMovie, iTunes, iPod, and eventually products ranging from that other iPhone to the iTrip and iToilet.

Now, with the iPhone, the “i” prefix continues to spread – this time to games and applications on the (get this) iTouch platform. We now have games like iDracula and apps like iBird Explorer Plus. It even extends to Mac apps like iStat Menus.

Apple is good at this kind of thing. If you think about it, Apple’s naming conventions go back as far as the “FirstNext” names for apps, like HyperCard and MacWrite, where the words are smooshed together with the second word retaining its capitalization. This naming convention has stuck all these years.

Like the ubiquitous “i” prefix, Newton product and app developers had their own prefix to work with: Newt. Just about everything that works with the Newton begins with “Newt” as a prefix.

There’s Newtris, the Tetris clone, or NewtTacToe. The web browser Newt’s Cape (say it fast for a variation of Netscape). Newtendo lets you emulate the Nintendo. Newtways let you connect peripherals. Stick “Newt” on the front of anything and you have a product for the Newton.

The prefix makes naming a product or application easy for the Newton. Take a bit of glue, glob it on the back of “Newt,” and attach it to whatever relates to the thing you want to promote. It’s easy because it doesn’t take much imagination or forethought. Like the “i,” you can throw it on anything and have a familiar-sounding yet brand-new product.

Some Newton developers used the “Newt” prefix in witty ways. Newt’s Cape is one of my favorites. Newtendo rolls of the tongue well.

But some are downright lazy. NewtGrocery? Really?

Thankfully, the “Newt” naming style didn’t last as long as the “i” prefix one has. We’re about 11 years and counting with that one, ever since Apple released the original iMac.

Maybe we could combine the two. iNewtToDo, anyone?

Riccardo Mori over at System Folder:

When your main system is capable of keeping multiple applications open, it’s easy to be distracted by incoming emails and updated RSS feeds. Not to mention the temptation to search the Web by following the spur of the moment — when that happens, the best case scenario is that I find myself two hours later digesting a lot of information I found following link after link, yet without doing anything really productive.

His solution? Write on a Mac Color Classic, or a Newton eMate 300 when away from home, to cut down on distractions.

“No browsers, no emails, no distractions: just me, my ideas, and the word processor,” Mori says.

It’s a brilliant (and, in a recession, cost-effective) solution to a problem a lot of us face every day. Why be productive when there’s another blog post to read? I’m working on my own, similar setup with my eMate 300.

Nice to see that Mori is getting something done on perfectly capable hardware.

Looking through the Newton Poetry archives, I realize that there are quite a few articles about how to do stuff – fax, connect with OS X, reset – that may have been lost in the shuffle.

Those articles are some of my favorites, because I’m learning how to do them at the same time you are. That’s what I like about writing Newton Poetry: getting my hands dirty with little projects. It’s a blast.

Connect your Newton with Mac OS X
One of the more popular features, this article explains how to use NCX to sync your 2.x Newton with a modern Mac running OS X. You can also learn how to connect with Escale and with NewTen.

Send a fax with your Newton
Faxing with your Newton is old school. The fax seems like an ancient technology, but with a 1.x or 2.x Newton and a simple modem, you can send faxes through the phone line.

Reset your Newton
Let’s say the worst happens, and your Newton somehow locks up or is frozen by a software error. There are different levels of restarting your Newton, and this post explains them all.

Take screenshots on your Newton
Recently, I learned how to take screenshots of my eMate using the Newton Toolkit. There are other, more complicated ways, but this one was the most immediately useful for my needs.

Install packages on your Newton
The Newton is kind of like the iPhone in that you can take it out of the box and it’s immediately useful and usable. But the fun part of owning one is installing cool apps that make it even more useful. That’s where installing .pkg files comes in handy.

Power your Newton with rechargeable batteries
This is more of a tip I learned when using my MP110. Instead of relying on my long-dead Apple battery pack, I bought some Eneloop batteries and used the heck out of them. Soon, I’ll be exploring more energy options with my eMate 300.

Read Newton eBooks
Not only is your Newton a pre-Amazon Kindle eBook reader, but there’s a plugin for Firefox that lets you read Newton eBooks in your web browser.

Since my eMate 300 arrived at the end of last summer, I’ve struggled with ideas on how to use it. I bought mine mainly as a testing machine; my MessagePad 110 could only run Newton OS 1.x applications, and I wanted to experiment with more recent Newton apps. Also, eMates don’t have the portability and flexibility of their MP2x00 cousins.

So, what to do? It’s only recently, as I think back to the eMate’s original use (education, writing, word processing), that I’ve thought of a practical use for the little green machine: a journal writer.

I’ve been a writer as long as I can remember. As a kid, I used a typewriter to hammer out short stories. When I discovered the computer, it opened up a whole new world for me. I grew up to be editor of my high school and college newspaper, earned my degree in journalism, and went on to be a professional public relations writer. I live and breathe the written word.

A few years ago, I picked up journaling after a long hiatus. A plain notepad and pen have been the victims of random thoughts since I graduated college in 2003. After using a keyboard for so long, though, I notice my hand fatigues after only a few paragraphs. It’s no laughing matter.

I thought about using one of my Mac SEs as a journaling machine, just as an excuse to turn on of the little guys, but the SEs lack the true portability I was looking for. Laptops are fine – I have two iBooks – but finding excuses to use my classic Apple hardware was the goal. The eMate was just what I was looking for in a writing machine.

At home, the eMate works fine. But the rechargable battery is dead, and it’s not like a standard MessagePad with replaceable batteries. The eMate’s battery is wired in. So my next project is to find a usable eMate battery and replace my dead one.

When that happens, the eMate’s portability will be good enough to carry with me on vacations, trips to the coffeeshop, and even local performances or exhibits, where I can type down my thoughts. The smaller eMate keyboard will take some getting used to, but I’ve used it a few times already, and it’s not that big of a change.

In the meantime, I’m going to use Newton Works (with, perhaps, a few add-ons) to keep an electronic journal. I may search for other word processor apps, just to test the options, and implement a folder structure by year for organization. Now that I have Newton-to-OS X syncing down pat, I can even export my entries as text files – just in case any of them work as a blog post.

It’s hard to justify owning an eMate just for testing and projects alone. Over time, I can think about other uses for it other than journaling – like recipe-keeping (that old cliché) or even Twittering. Who knows?

All this will give me an excuse to poke around the Newton 2.0 interface a bit more, try out some apps, and goof around with my newest Newton. Stay tuned – the next Newton Poetry post could be typed out on an eMate keyboard.

Just a heads up: Eckhart Köppen posted a wiki on his site, 40hz, that describes the 2010 Newton problem and some possible solutions. He also posted a wiki on patching the Newton.

Köppen is a Newton developer as well, and has posted some thoughts on how to do GTD on the Newton.

The good news is there are really smart people working on the Year 2010 issue, and Köppen seems to think getting a patch up and running will require “less black magic than anticipated,” as he told the Newtontalk list.

It’s right about now that people start to forget about that New Year’s Resolution they made in the weeks leading up to January 1. Exercise, diets, less boozing and puking in back alleys – these are the kinds of behaviors Americans swear to uphold with the coming of the new year.

I usually don’t make any resolutions except general ones, like trying to make this year better than the last. But I have changed one part of my daily routine: I joined a local gym. It was hard to resist. A $10-a-month postcard promotion was all it took to get me to become a member of my local Planet Fitness.

Fitness professionals and die-hards usually tell you to keep track of your progress. Weight, reps, body mass – all these things should be cataloged, the experts say, leaving nothing to chance. And since you don’t want to be seen as a Quitter by your friends and family, sticking with a fitness routine will ensure you’re carrying out your New Year’s Resolution until 2010.

The best part? You can use your Newton.

More… »

[Update: Ivan, in the comments, found the original Keyspan driver page.]

Last week, Leon pointed out that the pages containing Keyspan serial-to-USB adapters were nowhere to be found.

It’s true. Above is the page I landed on when I tried my own hyperlink. The page where Keyspan kept its USA-28x adapter driver was gone.

It turns out that a company called Tripp-Lite purchased Keyspan in May 2008 and dumped all the drivers somewhere else.

Keyspan USB adapters are considered the best in connecting your Newton MessagePad or eMate to Mac OS X. After a quick driver install, you can plug your Newton’s serial cable in one end of the Keyspan adapter, then plug in the adapter into your OS X Mac, and boom – full connection. If Newton users can’t find the Keyspan drivers, they can’t use the adapter.

And the new company, Tripp-Lite, doesn’t make it easy to locate the drivers. There’s a driver search page, and the USA-28x page, but it all takes some sleuthing.

This means that, after several blog posts on how to connect a Newton with an OS X Mac, I’ll have to update the Keyspan driver link. That’s not a big deal.

The big deal is Newton users struggling to find what they’re looking for.

[A big thanks to the Newtontalk gang for helping me locate the new driver pages.]

Steve Jobs and crew have some great ideas, but not all Apple innovations have come under his watch.

That’s the basis behind Mac|Life’s “Top 10 Innovative Apple Products – That Steve DIDN’T Dream Up” post.

Two items on that list are familiar: the Newton platform, and the eMate 300. Dreamed up by Apple’s Steve Sakoman, Steve Capps, and Larry Tesler (with help from then-CEO John Sculley), the Newton MessagePad and eMate were creations Steve Jobs had nothing to do with.

Mac|Life wonders: “And if Jobs hadn’t come along and killed it, who knows what might have been?”

[Image courtesy of State of the Ark.]

Microsoft Zune users weren’t the only ones suffering when 2009 arrived. Many, many Newton users were afflicted by the new year as well, thanks to an alpha-version “fix” of the infamous 2010 bug.

The problem hit the Newtontalk list on January 1. Jon Dueck described the situation that would become well-known to most Newton users who downloaded the Fix2010 patch: when his Newton clocked over from December 31, 2008, it immediately jumped to January 1, 2025. When he tried to change the date to 2009, as the Newton should have done at midnight, his Newton chose a July date in 2012.

Other users noticed the same bug. When some switched the date from 2025 back to 2009, everything worked fine. But for others, the system clock would register the correct date while the Dates app would display a 2025 date.

By process of elimination (and through a lot of e-mails traded back and forth), the list figured that Avi Dressman’s Fix2010.pkg was the culprit.

First, some background. The Newton 2010 bug has been well-known since at least 1998. My Apple Newton does a good job of breaking the bug down. Basically, Newtons running version 2.0 and above start getting weird dates behavior past the year 2010.

Avi Drissman’s Dates/Find BugFix extension (his other software is on his Newton page) was created to fix the 2010 bug in the Newton’s Dates application. His other “fix,” the “highly-experimental” Fix2010 package, originally released in September 1998, was meant to fix the 2010 bug system-wide.

Even Avi warns users:

Are you crazy? This is ALPHA-quality software. It has undergone almost no testing. It has not proved itself. It will not become useful for another 12 years. I wouldn’t recommend installing it. Period. Still want to install it? Back up your Newton. Totally. More than once. Do not install this on mission-critical machines. Really. Ensure that packages are installed on the internal store. Use the Newton Connection Utilities program that came with your Newton device to download the included package.

Can’t get a more dire warning than that, eh? But really, Avi’s message turned out to be more than a warning. It was pure prophecy.

Someone wrote Avi and asked him to release the source code for the Fix2010.pkg, which he did under BSD, so that others could work to fix the patch.

“It’s kinda freaky, isn’t it?,” Avi wrote back. “When I wrote Fix2010, 2010 was some abstract idea way out there. Now it’s looming, eh?”

Avi’s original source code has been posted to SourceForget.net, and Eckhart Koppen started a Wiki to explain more about the problems from Fix2010.

“The fix should in the end work out fine,” Eckhart says. “The main issue seems to be the boundary condition of moving from one hexade (1993-2009) to the next (2009-2025).”

Dennis Swaney (who warned me on January 4 about this issue) offers a unique solution: set your clock to 1999. “Everything will be accurate except for the year,” Dennis says.

The Fix2010 bug had very real consequences. Jon later reported a problem with his To-Do dates setting to 2024, with repeat To-Dos appearing after he reset the date. L. W. Brown had two of his MP2100s turn into bricks trying to fix the problem. Only a full hardware reset (and a backup file) restored his Newtons to working order.

One Newton user, Lionello, said his MP2000 has displayed “wild
chime/popup activity” after removing the Fix:

This morning I think I’m facing a problem that I suppose is generated from the removed patch. In december I’ve set an Alarm for a birthday (for tomorrow), and I had set a 24-h warning. Now this morning I fired up my Newton and the popup appeared, but now the Newton seems to be in a loop, it chimes continuously, and if I try to close the Snooze/delete alarm popup, it closes, but in less than a second it pops up again with a chime.

Woody recommends resetting, moving Dates data to a card, perform a brainwipe, reinstall from a backup, delete all the Dates data from the backup, then move the data from the card to the MessagePad.

The best fix? Don’t install the Fix2010.pkg. Not until a patch is released. It may even be best to wait until January 1, 2010.

Fresh on the heels of the Zune meltdown, The Unofficial Apple Weblog broke down a few Apple bugs that have plagued users in the past, with – prophetically – heavy emphasis on Newton flake-outs.

The bigger issue with this 2010 bug is that, for us Newton users, a fix may never be found without a resourceful programmer pulling late nights to find and fix the problem. Apple will never release a patch to fix the dates issue. The Newton is dead to them from a support standpoint. The fix will be up to the Newton community.

We’re on our own.

Any readers have an issue with the Fix2010 package and the new year?

[As a side note, I dropped the ball with this one. I should have been on this story. Around Christmas, I stopped checking my Newtontalk e-mail as often as I used to. Sure enough, the minute I do that, the Newton world goes crazy. Lesson learned.]